Name: Accell UltraAV K072C-014B
Brand: Accell
SKU: 303315
Rating: 91 (1 reviews)

manualAccell UltraAV K072C-014B

READ ME FIRST – SETUP INSTRUCTIONS

Thank you for purchasing the Accell UltraAV HDMI Distribution

Ampliﬁ er. This product is designed to provide an exceptional

performance and value. Please review the manual before operating and retain for future reference.

- CAUTION -

1. Ensure the matrix and receivers

have sufﬁ cient ventilation. Do not

cover ventilation openings. Do not

install in a conﬁ ned space.

2. Do not operate near source

of heat. Do not stack on top,

underneath or between other heat

generating unit/s including other

ampliﬁ ers.

3. Unplug power adapter if not

used for an extended period.

4. To prevent damage from power

surges, the unit should be plugged

into a surge protector or surge pro-

tected power source.

5. Do not use near liquid or areas

of heavy moisture.

6. Clean unit with a clean and dry

cloth only.

7. This unit cannot be serviced in

the ﬁ eld. Contact Accell if service is

required.

8. Do not open case, risk of shock -

shock hazard.

9. Do not modify power cord or use

the product if the power cord is

damaged.

Introduction

The UltraAV HDMI 4x4 Matrix and Distribution Amplifier featuring

HDBaseT accepts signals from up to 4 HDMI enabled audio/video sources

and distributes the signal to up to 4 HDMI enabled displays. The matrix

can be configured to send any input to any HDMI displays, monitors,

projectors or TV’s.

Over-Current and Over-Voltage Protection

The circuit boards are equipped with both over-current and over-voltage

protection and will automatically power down if encountered. The circuit

boards will restore automatically once the excessive current or voltage

has passed.

Package Contents

●HDMI Distribution Amplifier (Matrix) ●1 Power Adapter (for Matrix)

●4 HDBaseT Receivers ●4 Power Adapters (for Receivers)

●CD-ROM (for RS-232 control) ●4-Pair IR-TX and IR-RX

●Remote Control (with battery) ●Owner’s Manual

●2 Front Panel Mounting Ears (with 4 Screws)

Model Number:

K072C-014B

UltraAV

HDMI 4x4 Matrix

with HDBaseT

Setup

Note: All Cat5e/6 cables must be terminated to 568B standards.

Unsheilded (or properly terminated sheilded cable), solid core Cat5e,

Cat6, Cat6e, Cat7 or Cat7e cable can be used. Stranded core is not

suggested as it can reduce signal transfer. Recommended to use a

continuous length of cable terminated at the matrix and receiver ends.

With the matrix power switch in the OFF position, connect an HDMI High

Speed cable from the HDMI Output of the most commonly used audio/

video source to the HDMI Input 1 located on the rear of the matrix.

Similarly, connect the remaining source devices to the HDMI Input Ports

on the matrix.

Tips: Use the shortest length HDMI cables possible in each point

in the installation. Use only High Quality and High Speed HDMI

cables.

If desired, run a LAN cable from your network or router into the port

labeled LAN IN on the rear of the matrix.

Next, connect a Cat5e/6 cable to the HDBaseT Out 1 port on the rear of

the matrix. Connect the other end of the Cat5e/6 cable to the HDBaseT

IN port on the rear of the HDBaseT receiver positioned near the TV. Run

a short, High Speed HDMI cable from the HDMI Out port on the receiver

to the HDMI In port on the TV. If desired, two Ethernet ports are

provided on the rear of the receiver for connection to Internet enabled

TV and/or computer. Plug a provided power adapter into an AC outlet

and the other end into the HDBaseT receiver. Using the same steps,

connect the remaining audio/video sources to the matrix.

The matrix has internal memory that stores the system

information for faster switching. Please follow the steps in the

order listed: Turn ON the displays and ensure they are awake (not in

standby mode). Check the displays INPUT setting to ensure the correct

HDMI port is active.

Turn on the source devices and ensure they are awake (not in standby

mode). Connect the power adapter to the matrix. Plug the power

adapter into a surge protected AC power outlet. Turn the matrix power

switch to the ON position.

The matrix has a low power draw and is intended to be left on. If

the matrix is turned off, start up the system as noted above. If new

hardware is added, please perform a RESET.

To RESET the matrix, turn off the display and source devices. Power off

the matrix and unplug the power adapter from the rear of the matrix.

Wait 20 minutes for the memory of the system configuration inside of

the matrix to be deleted. Follow the setup instructions above to correctly

initiate the setup.

HDMI 4x4 Matrix and Distribution Amplifier Model: K072C-014BSpeciﬁ cations

● Independently access 4 HDMI Sources from 4 HDMI Displays

● Supports HD resolutions up to 1080P and 3D

● HDMI 1.4a, HDCP 1.2 compliant

● Audio formats supported: DTS-HD 7.1, Dolby True-HD 7.1

● Deep color up to 36-bit

● RS232 Port for control

● Maximum HDMI input/output cable length: Up to 16ft./5m

● Maximum Cat5e/6 output cable length: Up to 328ft./100m

● Supports up to 100 BaseT Ethernet, two ports per receiver

● 19” Rack Mounting (front panel mounting brackets included)

● 12V DC, UL Listed Power Supply for 4 x 4 Matrix Unit

● 5V DC, UL Listed Power Supplies for Receiver Units (4 Total)

● Matrix dimensions: 17.3”W x 2”H x 7.9”D (440W x 51H x 20D mm)

● Receiver dimensions: 4.4” W x .9” H x 3” D (112W x 23H x 76D mm)

● Operating temperature range: 5 to 131°F (-15 to 55°C)

● Operating humidity range: 5% to 90% RH (no condensation)

Ver el manual de Accell UltraAV K072C-014B aquí, gratis. Este manual pertenece a la categoría Extensores AV y ha sido calificado por 1 personas con un promedio de 9.1 . Este manual está disponible en los siguientes idiomas: Inglés . ¿Tienes alguna pregunta sobre Accell UltraAV K072C-014B o necesitas ayuda? Haz tu pregunta aquí

¿Necesitas ayuda?

¿Tiene alguna consulta sobre el Accell y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Accell proporcionarle una buena respuesta.

Número de preguntas: 0

General

	Accell
	UltraAV K072C-014B \| K072C-014B
	Extensor AV
	826388108257, 0826388108257
	Inglés
	Manual de usuario (PDF)

Características

Tipo	AV transmitter & receiver
Máxima resolución	1920 x 1080
Tipos de cable soportados	Cat5e, Cat6
Distancia de transferencia máxima	100
Sistema de audio	Multichannel
Formato de vídeo soportado	1080p
Ancho de banda	6.75
Interruptor de encendido/apagado integrado	✓
Ancho de banda	225
Color del producto	Black
Indicadores LED	✓

Puertos e Interfaces

Ethernet	✓
Puertos de entrada RJ-45	2
Puertos de salida RJ-45	4
Entrada HDMI	4
Tipo de serie de interfaz	RS-232
Cantidad de puerto serial	1
Enchufe de entrada de CC	✓

Condiciones ambientales

Intervalo de temperatura operativa (T-T)	-15 - 55
Intervalo de humedad relativa para funcionamiento	5 - 90

Control de energía

Voltaje de entrada AC	12
Adaptador de energía externo	✓

Peso y dimensiones

Dimensiones de receptor (Ancho x Profundidad x Altura)	112 x 76 x 23
Dimensiones del transmisor (ancho x largo x alto)	440 x 20 x 51

Contenido del empaque

Manual	✓
Adaptador AC incluido	✓

¿No puede encontrar la respuesta a su consulta en el manual? Puede encontrar la respuesta a su consulta en las preguntas frecuentes sobre el Accell UltraAV K072C-014B más abajo.

¿No aparece tu pregunta? Haz tu pregunta aquí

No hay resultados