ACCESSORIES
MINI LAN CABLE TESTER MT-7058 User’s manual
INTRODUCTION
The mini LAN cable tester complies
safety standard, compact size and lightweight
design for easy detection of good connectio
opens, crossed wires & split pairs by only one
touch testing. T
lights allow one person operation. Additional
non-contact voltage detection provides user
safety
patch cords with RJ-45, RJ-1
BNC connectors.
SAFETY
1.
Read all instruction in this manual befor
using this tester
in damage to the tester or injury to the user
2.
with part
the tester and/or injure the user
3.
workshops, responsible teachers or skilled
personnel must control the us
testererve this preca
may result in damage to the tester or injury
to the user
4.
Organizations or Regulatory
whose scope encompasses the use of this
tester failure to do so may result in damage
to the tester or injury to the user
5.
carried out by qualified servic
qualified electricians/tech
the dangers of.
6.
tester
the tester and /or injury the user
7.
use for longer than a month. Chemic
leakage from the battery could damage the
tester
PRODUCT FEA
1. Complies with CE safety standard
2. Automatically detect good connectio
opens, crossed wires & split pairs
3. Simple one button test
4. LEDs indicate connections and faults
5. T
LAN cables
6. BNC cable indicator
7. Non-contact voltage detection for user
safety
8. Long cable test more than 300 meters
9. Low power consumption
off function to preserve battery
SPECIFICA
1.
T
TIA
connectors, 2 to 6 connectors installed.
BNC cables with male connectors.
2.
S
3.
colors to indicate low battery
4.
5. Case Dimens ions:100*60*24.5mm(Lx
6.
7.
PRODUCT DESCRIPTION
1. BNC
2. Non-contact
indicator
3.
4. RJ-45/RJ-1 connector
5.
6.
7. RJ-45/RJ-1 connector
Female
BNC
Instruction
Pouch
OPERA
1.
The Mini LAN Cable T
main unit and a remote unit. The remote
unit stores conveniently on the bottom of
the main unit. It can be removed or
replaced by sliding it from left to right or
right to left respectively
2.
Once the remote and main units are
attached to the ends of the subject cable,
as described in 3.2 and 3.3, testing may
begin, simply press and release the test
button on the main unit, observe the LED
indicators, and note the beepi
comes from the main unit.
3.
3.1 Power LED:
The power LED should li
whenever the test button is pressed and
released. If the power LED turns red,
replace the battery
also indicate the test result, it will turn
red, except wire in “S
will turn green
3.2 No connection LED
If the remote is not connected to the
main unit with a cable, or the cable has
no intake conductors, the no connection
LED will light up and the beeper
sound for 4 times.
3.3 Straight/Crossover LED
When all of the appropriat
LEDs light up, the straight or
crossover LED also lights up, and the beeper
sounds for 4 times (8P8C 3 times), it
means the cable is all correct connectio
some of the LEDs do not light up, but
others light up, and the straight LED also
lights up, it means the cable is open.
If some of the LEDs light up inconsistently
and the straight LED also lights up, it
means the cable may be misconnected.
Please check in turn of lighted LED of
remote unit to identify
misconnected or change left side s
“S
the misconnection status step by step.
Note:
RJ-1
1/12 cables may have 2 cond
conductors, or 6 conductors. When testing 2
conductor cables, LED 4 ~ 5 must lig
4 conductor cables, LED 3~ 6 must light up
and for 6 conductor cables, LED 2~7 must
light up, and “STRAIGHT” LED also li
The numbered LEDs do not indicate a goo
connection exists; only shows connection
exists. If “Short” LED lights up during test, it
means the shorted was found in the cable.
3
.4 Short LED
If 3 & 4 LEDs lights up, and all other
LEDs do not light up, the cable is
shorted; the “short” LED will light up.
3.5 Crossover LE
Numbered 1~8 LEDs will light up, and
“Crossover” LED also lights up. Means
wiring one end with 568-A
and the other end with 568-B standard
4. BNC
Numbered LEDs will light up during
scanning, after scanning, both LEDs of
BNC on the main unit and the BNC receiver
will light up. If the BNC cable is short, only
the LED of BNC on the main unit lights up;
if the BNC cable is open, both
on the main unit and the receiver
and “no connection” LED will light u
5.
Non-contact V
Set the left side switch to the NCV position
and the right side switch to the Sound On
position.
right top of the testerclose right top of the
tester to the live wires, the LEDs of NCV
will flash with sound.
Pleas
e put the tester as close as
possible to surface of tested
source for optima testing result.
¿Necesitas ayuda?
¿Tiene alguna consulta sobre el Pro'sKit y la respuesta no está en el manual? Haga su consulta aquí. Proporcione una descripción clara y completa de su problema y su consulta. Cuanto mejor describa su problema y consulta, más fácil será para otros propietarios de Pro'sKit proporcionarle una buena respuesta.
Número de preguntas: 0